What Liquid To Use In Ultrasonic Cleaner

FAQ guide on how to get the all-time results from an ultrasonic cleaner.

FAQ'south for using an ultrasonic cleaner

How to get the all-time results from your ultrasonic cleaner.

Q. Is ultrasonic cleaning aggressive or abrasive?

No. An ultrasonic cleaner is not a replacement for a wire brush or emery cloth.

Q. How do I get the best out of my ultrasonic cleaner?

Ensure the component being cleaned is fully submerged in the fluid.
The should not touch the tank sides or base to permit maximum cleaning (use the basket).
Cheque the cleaning solution is at the right temperature.
Check the cleaning fluid is mixed in the correct ratio.

If you live in a hard water area, nosotros recommend using de-ionised, de-mineralised or distilled water as calcium carbonate and other impurities in tap water can reduce the cleaning properties of the solutions and produce undesirable side furnishings such equally lime scale deposits. If you lot alive in a soft water area, tap water should exist OK.

Q. Can I use solvents or other cleaning liquids in my ultrasonic tank?

Yes, but utilise with caution. Liquids and chemicals not specifically designed for apply with ultrasonic cleaners may cause a health chance if subjected to heat and ultrasonic agitation, besides as potentially dissentious the tank. In extreme cases, some flammable cleaning solvents tin can get unstable spontaneously combust. If in doubt, check with your chemical supplier.

DK Sonic 3 Ltr ultrasonic cleaner - dial control

three Ltr tank with dial control

half-dozen Ltr tank with dial control

Q. What cleaning solution or fluid should I utilise?

We sell a wide range of cleaning fluids suitable for most applications. Please visit: www.bestultrasonic.co.uk . Always bank check that the fluid y'all are using is suitable for the component you lot are cleaning. The chemical limerick of each solution is stated on it's data sheet.

Q. What ratio of water to cleaning fluid should I employ?

Always use the manufacturers recommended ratio for any cleaning fluid you are using. Fluids purchased from us have the mix ratio displayed on the characterization. Commonly this is ten:1 simply for heavy contamination, this tin can exist reduced to 7:1 for a stronger solution. More than info Hither

Q. What is 'Degassing' and how do I do it?

Degassing removes whatsoever gasses present in the cleaning fluid. Yous should do this whenever you use your ultrasonic cleaner as information technology volition assistance the cleaning process. Yous can degas your fluid by raising the temperature and switching on the ultrasonic ability. Degassing is consummate when bubbling stop rising and there are only ripples on the surface. Some of our ultrasonic cleaners have a degassing part built-in. However, if left for a few hours, air will ever ascent to the surface naturally. This is more relevant for the larger tanks (22 Ltr and above).

DK Sonic 2200D ultrasonic cleaner — DK Sonic 22 ltr ultrasonic cleaner with degassing

Q. Can I put my hand in the tank while the unit of measurement is running?

Not actually. Avoid putting hands in the cleaning solution, particularly if the ultrasonic is in operation. Non merely practise most cleaning solutions incorporate chemicals likely to cause peel irritation, but the action of ultrasonic energy in water can be harmful to human tissue.

Q. Why practice I demand to employ a handbasket in my cleaner?

Placing items direct in the tank causes them to come into contact with the base of the tank, which over time will harm the stainless steel and transducers which are attached at the underside of the unit of measurement. This volition disrupt the ultrasonic generation and if the items are heavy can actually harm the electronics. Although using a basket will marginally reduce the effectiveness of the ultrasonic action slightly, this is non normally significant. An alternative method, peculiarly for big items is to append them in the fluid using a cross-bar (welding rod or knitting needles) and wires to dangle them in the liquid which prevents your item sitting on then bottom of the tank.

Q. Why is information technology important to use my tank at the correct temperature?

Heating the tank will give better results to cleaning and also speed up the process – most solutions volition demand to be heated to perform equally designed. The optimum temperature setting for the cleaning fluid should be indicated on the label on the canteen. The fluids we sell work betwixt 50 – 80 degrees centigrade.

Q. How often should I change the cleaning fluid in my tank?

The cleaning fluid in the tank should be changed whenever it becomes visibly too contaminated, or when the cleaning process is not as effective. If you lot can't see the bottom of the tank, its fourth dimension to change the fluid!

Q. What is the wheel fourth dimension of my ultrasonic cleaner?

Most things clean in a few minutes. 5-10 minutes is sufficient for jewellery, whilst carburettors demand about 20 minutes depending on how contaminated the components are.

Q. What is the 'foil examination'?

If you lot feel cavitation (cleaning) is not occurring properly y'all should perform the 'foil test.

Fix your tank to its correct operating temperature and add any solution and degas the fluid. Suspend a piece of baking foil in the tank and switch on the ultrasonic power. After around 1 infinitesimal, inspect the foil. If the cleaner is operating correctly the foil should be perforated.

Q. Do I need to fill the tank to the meridian?

Ii thirds is OK equally a minimum fill up. One-half filling the tank with fluid is acceptable for pocket-size cycles, but you must ensure the heating element is not switched on.

Q. Exercise fifty need the lid on the tank whist cleaning?

No, it's not essential, but the lid prevents any gasses from the cleaning solution produced by the heating and ultrasonic procedure from escaping and it keeps the estrus in the fluid, and so saving power consumption.

Q. Can I clean heavy or dumbo items?

Heavy or dumbo items tin exist cleaned just they should not be placed on the bottom of the tank as this could damage the transducers. Instead they should be suspended in the bathroom by handbasket or other means such a wires.

Q. When the cleaning bike is finished do my items need rinsing?

Yes they do. Rinsing removes the residues of the cleaning fluid and any dirt or contaminants which may have been worked loose past the cleaning. Parts rinsed in de-ionised water will dry clear of water spots.

Q. Pocket-size parts will fall through the mesh of the basket – how do I clean them?

If the objects you wish to clean are too small for the basket identify them in a glass beaker which is too filled with cleaning solution. Then place that small-scale beaker in the cleaner. The ultrasonic waves are unaffected past glass and laissez passer through it, cleaning the items within. Practise not place the beaker directly on the bottom of the tank though equally this will result the operation of the ultrasonic emitters either suspend it in the solution, or place information technology within the wire handbasket. More info click Here

Q. Will the cleaner damage rubber seals in my carburettor?

No, provided that the rubber has not begun to perish.

Q. Practice I need to dismantle a carburettor earlier cleaning?

Yes. The more internal areas the cleaning fluid tin get to, the better the clean will be. If yous don't remove float bowls and jets etc, you will only clean the outside casting.